BEGIN:VCALENDAR
VERSION:2.0
PRODID:-//TYPO3/NONSGML Calendarize//EN
BEGIN:VEVENT
UID:calendarize-micro-project-bobbin-lace-meets-3d-printing-making-bracele
 ts-and-bookmarks-using-bobbin-lace-20260805-1
DTSTAMP:20260715T125302Z
DTSTART:20260805T140000Z
DTEND:20260805T170000Z
SUMMARY:Micro-project | Bobbin lace meets 3D printing: making bracelets an
 d bookmarks using bobbin lace
DESCRIPTION:This open workshop is aimed at anyone who would like to try th
 eir hand at bobbin lace-making (again). At the same time\, the workshop co
 mbines the craft of bobbin lace-making with new technologies: 3D-printed b
 eads are incorporated into bobbin-laced bracelets\, whilst bobbin-laced bo
 okmarks are sewn into frames produced by a 3D printer.\nBobbin lace bracel
 ets – the perfect introduction to bobbin lace-making and 3D printing! In
 cludes:\nSetting up the bobbins and attaching the threadCrossing and turni
 ng the bobbinsMaking the “braid”An introduction to 3D printingIncorpor
 ating beads from the 3D printer\nBookmark – a classic bobbin lace patter
 n following on from the ‘Flechter’\, includes:\nLearning to read bobbi
 n chartsMaking the linen stitchSewing the ribbon into a 3D-printed frame\n
 Both formats are always offered on the workshop date. The choice between a
  bracelet (beginner) and a bookmark (advanced) depends on the participants
 ’ existing level of knowledge. Recommended age: 8 years and over.\nA bas
 ic supply of materials is provided. Anyone who prefers to work with their 
 own materials is welcome to bring them along.\nThe studio is located on th
 e premises of Bunte Bude Chemnitz e. V. at Zöllnerstraße 18 in Chemnitz 
 (rear building\, last room on the upper corridor).
X-ALT-DESC;FMTTYPE=text/html:<p>This open workshop is aimed at anyone who 
 would like to try their hand at bobbin lace-making (again). At the same ti
 me\, the workshop combines the craft of bobbin lace-making with new techno
 logies: 3D-printed beads are incorporated into bobbin-laced bracelets\, wh
 ilst bobbin-laced bookmarks are sewn into frames produced by a 3D printer.
 </p>\n<p><strong>Bobbin lace bracelets – the perfect introduction to bob
 bin lace-making and 3D printing! Includes:</strong></p>\n<ul><li>Setting u
 p the bobbins and attaching the thread</li><li>Crossing and turning the bo
 bbins</li><li>Making the “braid”</li><li>An introduction to 3D printin
 g</li><li>Incorporating beads from the 3D printer</li></ul>\n<p><strong>Bo
 okmark – a classic bobbin lace pattern following on from the ‘Flechter
 ’\, includes:</strong></p>\n<ul><li>Learning to read bobbin charts</li><
 li>Making the linen stitch</li><li>Sewing the ribbon into a 3D-printed fra
 me</li></ul>\n<p>Both formats are always offered on the workshop date. The
  choice between a bracelet (beginner) and a bookmark (advanced) depends on
  the participants’ existing level of knowledge. Recommended age: 8 years
  and over.</p>\n<p>A basic supply of materials is provided. Anyone who pre
 fers to work with their own materials is welcome to bring them along.</p>\
 n<p>The studio is located on the premises of Bunte Bude Chemnitz e. V. at 
 Zöllnerstraße 18 in Chemnitz (rear building\, last room on the upper cor
 ridor).</p>
LOCATION:Chemnitz\, Bunte Bude Chemnitz e.V.
END:VEVENT
END:VCALENDAR